Archive:AirCasting Shield: Difference between revisions
Jump to navigation
Jump to search
You are visiting an old member project. The information found on "AirCasting Shield" might be out of date. See Archive:Environmental Monitor which is the follow up project
(Pictures \o/) |
mNo edit summary |
||
| (6 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
{{outdated|type=member project|moretext= See [[Archive:Environmental Monitor]] which is the follow up project}} | |||
{{project | |||
|name = AirCasting Shield | |||
|status = obsolete | |||
|image = Aircasting_rev01_06.jpg | |||
|description = Arduino shield for [http://www.aircasting.org/ AirCasting] | |||
|author = | |||
|username = tiefpunkt | |||
|version = Rev. 01 | |||
|update = | |||
|platform = | |||
|license = | |||
|download = https://github.com/tiefpunkt/AirCasting-Shield | |||
}} | |||
Arduino Shield for [http://www.aircasting.org/ AirCasting]. Simpler than their wiring mess. | Arduino Shield for [http://www.aircasting.org/ AirCasting]. Simpler than their wiring mess. | ||
== | == Revision 1 == | ||
=== | === Hardware === | ||
* Sensors: SHT22, MQ-7, MQ-135 | * Sensors: SHT22, MQ-7, MQ-135 | ||
** Proper heater drive for MQ-7, thanks to Citizen Sensor [http://thesis.jmsaavedra.com/prototypes/technology/mq-7-carbon-monoxide-sensor-breakout/] | ** Proper heater drive for MQ-7, thanks to Citizen Sensor [http://thesis.jmsaavedra.com/prototypes/technology/mq-7-carbon-monoxide-sensor-breakout/] | ||
* Board: Prototype milled at OHM2013 | * Board: Prototype milled at OHM2013 | ||
* Issues: | * Issues: | ||
** MQ-* sensors didn't fit into their holes -> holes to small. Also pads to small, soldering was a pain and required some hacking to the board. | ** MQ-* sensors didn't fit into their holes -> holes to small. Also pads to small, soldering was a pain and required some hacking to the board. | ||
| Line 12: | Line 27: | ||
** Sensors get quite warm | ** Sensors get quite warm | ||
==== Pictures | === Software === | ||
Arduino firmware, using some [http://fluuux.de/2012/10/arduino-temperatur-und-luftfeuchtigkeit-mit-dem-dht22-prufen/ DHT22 Tutorial] and this [http://thesis.jmsaavedra.com/prototypes/software/mq-7-breakout-arduino-library/ MQ-7 Library] (with a few changes to fix stuff) for proper heater driving. | |||
* DHT22 returns legit data | |||
* MQ135 could be legit | |||
* MQ7 is oddly low. | |||
* Both gas sensors can't report real ppm values, as they would have to be calibrated. | |||
* Bluetooth works fine. | |||
=== Pictures === | |||
{| | {| | ||
| [[File:Aircasting_rev01_01.jpg|200px|thumb]] | | [[File:Aircasting_rev01_01.jpg|200px|thumb]] | ||
| Line 22: | Line 45: | ||
| [[File:Aircasting_rev01_06.jpg|200px|thumb]] | | [[File:Aircasting_rev01_06.jpg|200px|thumb]] | ||
|} | |} | ||
== Revision 2 == | |||
Phase: Planning | |||
* Can keep DHT22 sensors | |||
* Should switch so electrochemical sensors for gases. | |||
** Nemoto NAP-505 [http://www.nemoto.eu/nap-505.html] | |||
** Figaro TGS5342 [http://www.figaro.co.jp/en/tech/index.php?mode=detail&id=94] | |||
** e2v EC4-500-CO [http://www.sgxsensortech.com/site/wp-content/datasheets/electrochem/EC4-500-CO.pdf] | |||
[[Category:Project]] | [[Category:Project]] | ||
Latest revision as of 16:34, 10 September 2022
You are visiting an old member project. The information found on "AirCasting Shield" might be out of date. See Archive:Environmental Monitor which is the follow up project| AirCasting Shield Release status: obsolete [box doku] | |
|---|---|
| |
| Description | Arduino shield for AirCasting |
| Last Version | Rev. 01 |
| Download | https://github.com/tiefpunkt/AirCasting-Shield |
Arduino Shield for AirCasting. Simpler than their wiring mess.
Revision 1
Hardware
- Sensors: SHT22, MQ-7, MQ-135
- Proper heater drive for MQ-7, thanks to Citizen Sensor [1]
- Board: Prototype milled at OHM2013
- Issues:
- MQ-* sensors didn't fit into their holes -> holes to small. Also pads to small, soldering was a pain and required some hacking to the board.
- Relais fairly loud.
- Sensors get quite warm
Software
Arduino firmware, using some DHT22 Tutorial and this MQ-7 Library (with a few changes to fix stuff) for proper heater driving.
- DHT22 returns legit data
- MQ135 could be legit
- MQ7 is oddly low.
- Both gas sensors can't report real ppm values, as they would have to be calibrated.
- Bluetooth works fine.
Pictures
Revision 2
Phase: Planning
