From The Munich Maker Lab's Wiki
Revision as of 20:51, 9 May 2023 by C22 (talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search


  • SSID: "munichmakerlab" (supports 2.4 GHz and 5 GHz)
  • Security: WPA2 Personal. Preshared Key is on a sticker located on the mailbox at the workshop door.

Network Segments

Network Subnetmask Gateway DNS servers DHCP server VLAN Comment
SpaceNET (/16), 50 If you don't know what this is, this is the network you are using.
Mgmt LAN (/24) none (administrative purposes)
SpaceVPN (/24) none Restricted access to SpaceNET and Mgmt VLAN
PPPoE VLAN - - - - 3 (administrative purposes)
Reserved VLAN - - - - 2019 Do not use
Reserved VLAN - - - - 2020 Do not use
Reserved VLAN WB³ (/23) 2012 Do not use

SpaceNET: IP Address Space

  • Space-Stuff (space owned or used stuff): -
  • User-Stuff static IP: -
  • User-DHCP: - (lease time 1 week)

SpaceNET: Getting a fixed IP address

If you need a fixed IP address, choose one that's not taken in the appropriate range and enter it in the table below. Usually there are groups of IPs (3D printers, ...) so try to fit your device in one of the groups.

SpaceNET: Allocated IP Addresses

IP Address Name Description Router Router ns1 DNS server (running on the docker01 host) DO NOT USE DHCP Range NyanPrint Color Laser Printer / Drucker Kyocera FS-C8020MFP OctoPrint NEO 1 Neo1 http://neo1.local/ OctoPrint X400 x400 OctoPrint Zonestar Z5 Zonestar Z5 (duplicate) vertexdelta OctoPrint Vertex Delta Ultimaker Ultimaker "Ulrich" Unlimited Z (duplicate) OctoPrint X350 X350 http://x350.local/ Koukaam Netio-230A Spannungsverteilungsgerät Led panel LED Panel heimdal Door Lock RPi strichliste strichliste backend on Chris' ProxMoxBox zuko-ng zuko rusa Prusa Mini 1 Prusa Mini lusa Prusa Mini 2 Prusa Mini docker01 Docker Host docker01-old Old Docker Host while stuff is being migrated over Lasercutter LaserCutter LaserPC LaserCutter LaserCutPC OLD (temp) LaserCutter cutmysignintopieces Plotter MuMaShare MuMaShare Paul's storage box raspi Paul Wasserschaden Paul (bridge to the mesh) germanpi A very German Pi MuMaMox Chris' ProxMoxBox

SpaceNET: Dead Hosts

IP Address Name Description NyanerPrint HP Color LaserJet cm2320fxi MFP OctoPrint X400 X400 http://x400.local/ tokyo.local LED-Panel eth0 tokyo.local LED-Panel wlan0 hawking Fileserver (deactivated) ewindow Virtual Machines


We got native IPv6 \o/


DNS is provided by a docker bind image (

  • Internal zone is "", not all hosts are in there yet
  • Server is maintained via Webmin at


Should make sense.


Currently rolling a Ubiquiti setup with USG, CloudKey, 24-Port US-24 Switch, UAC PRO access point and a AP-PRO access point for the "Feuerwehr" access (toilets). Infrastructure is centrally managed up to the access switch (ground level switches) which all terminate the MuMaLab Network unless stated otherwise.


We are connected to the internet via a Telekom V-DSL connection. Speed is usually 100 mbit down, 40 up.


VPN is provided for administrative purposes, contact Severin or German for more information.