CNC3018 Pro
Warning: This page is still a work in Progress, please contact Yichen Zhang (Spacezhang) on Slack if more Information is needed
Warning: Beware of the dangers of CNC machines! Use at your own risk and only if you know what exactly you are doing! Please contact Yichen for detailed explaination and tutorial
| CNC 3018 Pro Release status: experimental [box doku] | |
|---|---|
| |
| Description | Milling/ Engraving Machine |
| Author(s) | Yichen Zhang (Spacezhang) |
| Last Version | v0.1 pre alpha test (25.04.2022) |
General Introduction
A small but full-featured cnc running GRBL donated to the lab for use, brought to you and maintained by Yichen.
What is the CNC 3018 Pro?
The CNC 3018 Pro is a generic engraving machine. This machine can be used to cut anything from wax to wood and is very good for getting started and learn how to use a CNC machine and how It works.
Acceptable work piece materials
Engrave/ Cut
- MDF / HDF
- Softwood, Hardwood, Plywood
- Acrylic
- PCB
- Very soft Aluminium (no harder than brass or aluminum 6061) (Detail untested)
+ Height Map support
Current Machine Location
The CNC 3018 Pro is currently on the right side shelf in the machine workshop.
Getting started
Basic operation
- Change Router bits
- Change Spindle
- Z Height map
Please Inspect the machine in regards of integrity before Use!
Please check:
- Is all cable connected correctly and in tact?
- Is the linear rods and drive screw damage free?
[Detail and Tutorial comming soon]
Software Setup & Introduction
Set up the machine -> connect to laptop -> move to origin -> load sample gcode -> start milling
Wood Engraving / Milling
PCB Engraving
Acrylic Engraving / Milling
Test Gcode
[Detail comming soon]
Maintanence
[Detail comming soon]
Material settings
Machine Inventory
Technichal Documentations
Specifications
Mechanical Specifications
- Type: Milling / Engraving machine
- Machine dimensions: 330 x 400 x 240 mm (13.0″ x 15.7″ x 9.4″)
- Working area: 300 x 180 x 45 mm (11.8″ x 7.1″ x 1.8″)
- Frame: Extruded Aluminum
- Linear system: Lead screw driven with rods and linear bearings
- Materials: Woods, Plastics, PVCs, soft aluminum (6061), Nylon, Acrylic, PCBs
- Motion: NEMA 17 Stepper motors
Spindle
- Motor: 775 motor, 24 V , ~8,000 RPM
- Rated current: 1.2A @ 24V.
- Cooling Fan: Internal
- Overall Size: 98x42mm, Full Round Type Ø5mm shaft.
- Collets: ER 11
Routing Bits
- Currently only 3.175 mm (1/8 Inch) Bits Available
- V Bits 20 / 40 / 60 degree
- Multifunctional cutting bits 0.8 – 3.175 mm
- Single flute upward cutting bits 3.175mm, 2mm
- 3.175mm Ball end double flute bits
Controll Board
- Woodpecker V3.4 Mainboard
- Running GRBL 1.1f
- Interface Compatibility: Windows, Mac OS, Linux
[Detail comming soon]
Ongoing upgrades
- Vaccume chip suction adapter
- Emergency Stop around front panel
- New Waste Board
- Different diamenter ER11 Collets holder
Possible Improvements
- Install End Stops
- Drag Knife cutter for vinyl Logo Cutting
- Better Z – Probe
- Laser Module for laser cutting / Engraving
- Chip suction device
- Second better waste Board
- Spindle Upgrade for better cutting
[Detail comming soon]
Sample cuts and demonstration projects
MuMaLab Acrylic Cut
PCB Trace Test
Engraving Test of a sticker in lab
A PCB for a university project
A PCB for a university project
Prototype PCB for the Router Lift project
Prototype PCB for the Router Lift project
Replacement part list
Current GRBL Settings
GRBL 1.1f $0=10 $1=25 $2=0 $3=2 $4=0 $5=0 $6=0 $10=1 $11=0.010 $12=0.002 $13=0 $20=0 $21=1 $22=0 $23=0 $24=50.000 $25=500.000 $26=250 $27=1.000 $30=1000 $31=0 $32=0 $100=800.000 $101=800.000 $102=800.000 $110=1000.000 $111=1000.000 $112=800.000 $120=30.000 $121=30.000 $122=30.000 $130=200.000 $131=200.000 $132=200.000
Feedback and suggestions
If you have any feedback, request or suggestions in regard to this project and wiki page, please feel free to contach me or simply edit this section of wiki.
Feedback/Request/suggestions:
