Network
WiFi
- SSID: "munichmakerlab" (supports 2.4 GHz and 5 GHz)
- Security: WPA2 Personal. Preshared Key is on a sticker located on the mailbox at the workshop door.
Network Segments
| Network | Subnetmask | Gateway | DNS servers | DHCP server | VLAN | Comment |
|---|---|---|---|---|---|---|
| SpaceNET | 255.255.0.0 (/16) | 10.10.0.1 | 10.10.0.10, 10.10.0.1 | 10.10.0.1 | 50 | If you don't know what this is, this is the network you are using. |
| Mgmt LAN | 255.255.255.0 (/24) | 10.11.1.1 | 10.11.1.1 | 10.11.1.1 | none | (administrative purposes) |
| SpaceVPN | 255.255.255.0 (/24) | 10.11.2.1 | 10.11.2.1 | 10.11.2.1 | none | Restricted access to SpaceNET and Mgmt VLAN |
| PPPoE VLAN | - | - | - | - | 3 | (administrative purposes) |
| Reserved VLAN | - | - | - | - | 2019 | Do not use |
| Reserved VLAN | - | - | - | - | 2020 | Do not use |
SpaceNET: IP Address Space
- Space-Stuff (space owned or used stuff): 10.10.20.0 - 10.10.20.100
- User-Stuff static IP: 10.10.20.101 - 10.10.20.254
- User-DHCP: 10.10.10.20 - 10.10.11.250 (lease time 1 week)
SpaceNET: Getting a fixed IP address
If you need a fixed IP address, choose one that's not taken in the appropriate range and enter it in the table below. Usually there are groups of IPs (3D printers, ...) so try to fit your device in one of the groups.
SpaceNET: Allocated IP Addresses
| IP Address | Name | Description |
|---|---|---|
| 10.10.0.1 | Router | Router |
| 10.10.0.10 | ns1 | DNS server (running on the docker01 host) |
| 10.10.10.20-10.10.11.250 | DO NOT USE | DHCP Range |
| 10.10.20.10 | NyanPrint | Color Laser Printer / Drucker Kyocera FS-C8020MFP |
| 10.10.20.24 | OctoPrint NEO 1 | Neo1 http://neo1.local/ |
| 10.10.20.25 | OctoPrint X400 | x400 |
| 10.10.20.26 | OctoPrint Zonestar Z5 | Zonestar Z5 |
| 10.10.20.27 | vertexdelta | OctoPrint Vertex Delta |
| 10.10.20.28 | Ultimaker | Ultimaker "Ulrich" Unlimited Z |
| 10.10.20.27 | OctoPrint X350 | X350 http://x350.local/ |
| 10.10.20.40 | heimdal | Door Lock RPi |
| 10.10.20.42 | strichliste | strichliste backend on Chris' ProxMoxBox |
| 10.10.20.44 | zuko | |
| 10.10.20.45 | rusa | Prusa Mini 1 Rusa |
| 10.10.20.46 | lusa | Prusa Mini 2 Lusa |
| 10.10.20.66 | docker01 | Docker Host |
| 10.10.20.67 | docker01-old | Old Docker Host while stuff is being migrated over |
| 10.10.20.80 | Lasercutter | LaserCutter |
| 10.10.20.81 | LaserCutPC | LaserCutter |
| 10.10.20.85 | LaserCutPC OLD (temp) | LaserCutter |
| 10.10.20.82 | cutmysignintopieces | Plotter |
| 10.10.20.90 | MuMaShare | MuMaShare |
| 10.10.20.123 | Paul's storage box raspi | Paul |
| 10.10.20.144 | Wasserschaden | Paul (bridge to the mesh) |
| 10.10.20.155 | germanpi | A very German Pi |
| 10.10.20.200-210 | MuMaMox | Chris' ProxMoxBox |
SpaceNET: Dead Hosts
| IP Address | Name | Description |
|---|---|---|
| 10.10.20.11 | NyanerPrint | HP Color LaserJet cm2320fxi MFP |
| 10.10.20.28 | OctoPrint X400 | X400 http://x400.local/ |
| 10.10.20.31 | tokyo.local | LED-Panel eth0 |
| 10.10.20.32 | tokyo.local | LED-Panel wlan0 |
| 10.10.21.61 | hawking | Fileserver (deactivated) |
| 10.10.20.150 | ewindow | Virtual Machines |
IPv6
We got native IPv6 \o/
DNS
DNS is provided by a docker bind image (https://github.com/sameersbn/docker-bind).
- Internal zone is "intern.munichmakerlab.de", not all hosts are in there yet
- Server is maintained via Webmin at https://10.10.20.66:10000/
Hostnames
Should make sense.
Hardware
Currently rolling a Ubiquiti setup with USG, CloudKey, 24-Port US-24 Switch, UAC PRO access point and a AP-PRO access point for the "Feuerwehr" access (toilets). Infrastructure is centrally managed up to the access switch (ground level switches) which all terminate the MuMaLab Network unless stated otherwise.
Uplink
We are connected to the internet via a Telekom V-DSL connection. Speed is usually 100 mbit down, 40 up.
VPN
VPN is provided for administrative purposes, contact Severin or German for more information.
