Smart Meter Hacking

     

Smart Meter Hacking Release status: experimental [box doku]
Description	Trying to read radio signals from smart meters e.g. by using the CC1101 (low cost, low power sub-1GHz RF transceiver)
Author(s)	Uli
Download	http://www.ti.com/lit/ds/symlink/cc1101.pdf

Introduction

Goal of the project is to do smart home stuff, especially reading smart meter data without having to buy proprietary, expensive, insecure devices from datahungry, privacy-ingorant and profitmaximizing companies. Therefore alternative hardware and open source "smart home"/"IoT" solutions such as [FHEM] [openHAB] or [Homegear] are preferred. Since Uli already has some smart meters installed in his flat from the energy billing company [Ista] who use the TI CC1101 radio transmitter in their metering devices. Reading the emitted radio signals from these (or similar) devices might be the first step to get a data source and therefore an overview of water, electricity and heating consumption in an open source smart home environment.

Original Metering Hardware

• smart water meters "domaqua m" (Ista istameter product brochure)
• heating meter "sensonic II" (Ista sensonic II product brochure (german))
• smoke detectors (Ista fumonic 3 product brochure)
• basestation "memonic3 radio net" usually installed in the stairways to collect and store radio signals from smart meters of multiple apartments and send them through a VPN tunnel via GPRS to Ista servers

• 

  Water meter Ista "domaqua m" with "radio net 3" module

• 

  Heating meter Ista "Sensonic II"

• 

  Basestation Ista "memonic 3"

Own Hardware

• raspberry pi with cc1101 to read 868 Mhz radio signals
• bought a cold and warm water meter for tinkering - unfortunately they do not have a radio module (radio net 3) installed opposed to what I was expecting (ISTA Wasserzähler, Kaltwasser, Istameter)
• got a memonic3 radio net device to read, aggregate and upload data from multiple smart meters [[1]]

<gallery>

Approach

• Try to get the CC1101 to send and receive data
  • Ideally mount it on an arduino nano which is then called a CUL (cc1101 USB lite) [DIY manual (german)]
  • Alternatively use an SDR to record and analyze radio signals from smart meters and try to unterstand them
• Integrate it in a wireless home server such as FHEM
• Display the data on something like grafana

Status

• trying to build my own nanoCUL [as described here]
  • first on a breadboard with arduino uno r3 ([pinout for nano here])

History (in reverse order)

• bought some extra CC1101's to build a nanoCUL without having to de-solder the old wire from my first CC1101 chip
• got some smart meter hardware for tinkering on ebay ("domaqua m" meter unfortunately without radio modules and a [memonic 3 radio net] (Memonic_3_radio_net_board.jpg opened))
  • the memonic 3 collects and store radio signals from CC1101 and sends them regularly to Ista via GPRS
  • it also contains a lot of Texas Instruments chips including CC1101 (of course) an [M430F417 microcontroller] and [Sierra Wireless AirPrime (Model Q2686RD)] GSM transceiver module together with a SIM Card and a 10 year battery
• recorded some smart meter radio signals with SDR (File:Smart meter signal.aup.zip)
  • signal not yet analyzed since I did not succeed to make GNUradio run on my macbook (with homebrew which seems unfortunate in this case)
• soldered some wire to the cc1101 to use it with raspberry pi serial connection similar to [like this] and made it send test data [used software to send data from here] which could be seen with SDR (thx Paul) in a waterfall chart
  • could not find proper firmware for reading ista radio signals though and don't have time and knowledge to build one
• ordered a CC1101 radio module

Links

[CC1101 Specs]

[Detailed description of mbus protocol]

[ista product brochure m-bus system (german)]

[ista protocol description mbus (german)]