Archive:DustCollectionSystem: Difference between revisions

From The Munich Maker Lab's Wiki
Jump to navigation Jump to search
No edit summary
m (Vrs moved page DustCollectionSystem to Archive:DustCollectionSystem without leaving a redirect)
 
(4 intermediate revisions by 3 users not shown)
Line 1: Line 1:
{{outdated}}
Our workshop should have a dust collection system for woodworking.  
Our workshop should have a dust collection system for woodworking.  


A fixed system should be in place which has a couple of outlets with blast gates and flex hoses to connect wood working power tools as needed.  
A fixed system should be in place which has a couple of outlets with blast gates and flex hoses to connect wood working power tools as needed.  


First pitch: 100mm PVC pipe under the roof along the brick wall with 3 down pipes (y-junction). Each down pipe has a blast gate and a 100mm to 50/35/?? mm outlet. Fixed, smooth pipe wherever possible, flex hose only where necessary. This ensures maximum flow.
Since we only have machines with small extraction outlets < 60mm the large (4 inch / 100mm) dust collector is not feasable for them.  
It might howewer be used for the CNC machines.


Risk of sparks in pipes is considered minimal. If there are valid concerns concerning sparks, putting bare copper wire inside the tubes and ground them is a common solution.
Find a cheap, used shop vac with automatic switch on.
Or
build own housing for an vacuume motor with an automatic switch. (https://www.amazon.de/Eltako-4825410-AR12DX-230V-Stromrelais/dp/B001BBZVU6/ref=sr_1_25?keywords=Einschaltautomatik&qid=1577803443&sr=8-25)
 
Connect vaccum to a zyklon dust seperator. Run some pipes from the zyklon to 1 or 2 wall plugs where a flex hose can be connected (https://www.amazon.de/Original-K%C3%A4rcher-Universal-Schlauchkupplung-Plus-Staubbeutel-Profi%C2%AE/dp/B07254F29R/)
 
https://www.mersch-reinigungstechnik.de/shop/wg/nass-trockensauger/muffen-und-adapter/


If allowed, drill a 100mm hole in the wall and blow *filtered* exhaust outside.


Estimated material costs: ~200-300 €


* https://www.amazon.de/POWERTEC-70201-4-Zoll-three-machine-Staub-Collection/dp/B01N21P1WE
* https://www.amazon.de/Absperrschieber-für-Absauganlagen-Kunststoff-100/dp/B01M0S2JIK
* https://www.amazon.de/Flexrohr-Flexibler-Meter-Flexschlauch-Schlauch/dp/B00FCGR7TO
* https://www.amazon.de/Schlauch24-Absaugschlauch-mit-Stahldrahteinlage-76mm/dp/B0752G24JW
[[Category:Project]]
[[Category:Project]]

Latest revision as of 15:16, 10 September 2022

Attention.png You are visiting an old wiki page. The information found on "DustCollectionSystem" might be out of date.

Our workshop should have a dust collection system for woodworking.

A fixed system should be in place which has a couple of outlets with blast gates and flex hoses to connect wood working power tools as needed.

Since we only have machines with small extraction outlets < 60mm the large (4 inch / 100mm) dust collector is not feasable for them. It might howewer be used for the CNC machines.

Find a cheap, used shop vac with automatic switch on. Or build own housing for an vacuume motor with an automatic switch. (https://www.amazon.de/Eltako-4825410-AR12DX-230V-Stromrelais/dp/B001BBZVU6/ref=sr_1_25?keywords=Einschaltautomatik&qid=1577803443&sr=8-25)

Connect vaccum to a zyklon dust seperator. Run some pipes from the zyklon to 1 or 2 wall plugs where a flex hose can be connected (https://www.amazon.de/Original-K%C3%A4rcher-Universal-Schlauchkupplung-Plus-Staubbeutel-Profi%C2%AE/dp/B07254F29R/)

https://www.mersch-reinigungstechnik.de/shop/wg/nass-trockensauger/muffen-und-adapter/