LaserCutter/Log

2018

Date	User	State	Notes
May 11th	David	✅	Laser was calibrated and filters were replaced. Working for now, but a complete overhaul is necessary. Installed lens: 75mm
Mar 28th	Severin	🛑	Can't cut through 5mm MDF; 3mm MDF needs way to much power -> probably needs recalibration. Do not use until then.
Jan 28th	Eax	✅	Installed the 75mm lens. Put a sign indicating the installed lens on the top cover of the Cutter.
Jan 14th	Eax	✅	Laser IN order! Housing was closed, replacement part were cut for future maintenance.
Jan 9th	Eax	🛑	Laser out of order, not to be used. Laser mirrors are adjusted and calibrated. Housing needs to be closed. Beam combiner needs to be mounted and positioned correctly.

2017

Date	User	State	Notes
Dec 23rd	Eax	🛑	Laser out of order, not to be used. The drift has been corrected by balancing the position of the mirrors and the linear rails. What still remains to be done is the *angular* alignment of the mirrors and the laser tube. The positional alignment of the mirrors has been corrected at this time. The first mirror was assembled 8mm to high for the first linear rail, and there was a misalignment of 3mm in the horizontal direction.
Dec 1st	Eax	🛑	Laser out of order, not to be used. Mirror cover on the laser tube itself was loose, because presumably s.o. tried to attach a too tight pilot laser holding assembly. Fixed the mirror cover to its place by using glue.
Nov 29	Eax	🛑	Laser out of order, not to be used. Replaced all three mirrors with the new batch of mirrors. Determined that the position of the 1st mirror is not aligned with the linear axis of the 2nd mirror (X axis movement). This leads to a drift of the spot on the 2nd mirror. The position of the first mirror needs correction. For this a pilot laser (red visible) would be ideal.
Nov 2nd	Tiefpunkt	🛑	Laser out of order, not to be used. Mirror 2 was loose again, after retightning not really alligned. Before realigning, mirrors should be switched for the now ones, which should fit the mirror mounts much better. Peter tried some calibration, but one of the screws of mirror 2 was too tight and the plastic handle on it broke. Reattached with superglue.
Oct 19th	Siedi	✅	Replaced SSR for the exhaust air. The switch is working again.
Oct 18th	Eax	✅	Laser cutter is operable. Air compressor was removed from the frame. Water protect issue not reproducible. 75mm lens assembled. 50mm lens is missing.
Oct 14th	Eax	✅	Laser is calibrated. BUT: Air compressor not working AND "Water protect" triggered every now and then.
Oct 7th	Tiefpunkt (talk)	⚠️	SSR of exhaust broken, won't turn exhaust off. Severin will get a replacement part.
Oct 5th	Tiefpunkt (talk)	🛑	Laser out of alignment again after longer laser job. Mirror assembly no. 2 gets warm, and loosens screw again. Repeated hot-cold cycles will make it the screw loose and the mirror wiggle out of position. Laser deemed not usable until realignment incl. mirror no. 1 as well. We'll look for a replacement mirror as well.
Sep 30th	Tiefpunkt (talk)	✅	Laser out of alignment again. Mirror No. 2 loose inside its holder. Mirror assembly screwed out of holder, mirror cleaned, and put back into assembly. Assembly holds 25mm mirrors, but the mirror seems slightly bigger, thus does not sit flush in the assembly, just jammed in there as tight as possible. Mirror put back in, and mirror no. 2 realigned, works fairly well for now.
Sep 28th	Tiefpunkt (talk)	✅	Laser aligned by Peter